List of Supported Transceiver Modules: Difference between revisions
No edit summary |
|||
Line 44: | Line 44: | ||
== List of tested third-party modules == | == List of tested third-party modules == | ||
The following list of modules have been either tested by Allegro or customers and have been reported to operate. Please be aware that this can change due new module revisions. | The following list of modules have been either tested by Allegro or customers and have been reported to operate. Please be aware that this can change due new module revisions. | ||
{| class="wikitable" | {| class="wikitable" | ||
Line 93: | Line 93: | ||
|- | |- | ||
| QSFP28 || Flexoptix Q.851HG.02 || Fiber (SR4) || | | QSFP28 || Flexoptix Q.851HG.02 || Fiber (SR4) || | ||
|- | |||
| QSFP28 || Flexoptix Q.161HG.10 || Fiber (LR4) || | |||
|- | |- | ||
| QSFP28 || fs.com 75308 || Fiber (SR4) || | | QSFP28 || fs.com 75308 || Fiber (SR4) || |
Revision as of 10:48, 19 June 2020
DISCLAIMER
Allegro Packets allows you to use third-party vendor modules in its appliances but guarantees only warranty and support for transceiver modules sold by Allegro Packets. Any malfunction or configuration issue with third-party modules are NOT covered by the warranty.
Allegro Packets does not restrict the use of third-party SFP+ modules for the devices. However, some hardware limitations apply which are described as follows:
Built-in ports vs. expansion cards
The Allegro Network Multimeter 1000/1200/3000/3200 series have two on-board SFP+ ports which are restricted to original or branded Intel modules.
All non built-in ports are not vendor locked and can accept all transceiver modules. However, there are modules that do not work because of specific vendor extensions within the modules. This applies for all ports of the Allegro Network Multimeter x300 and x500 series and all expansion cards for the Allegro Network Multimeter 1000/1200/3000/3200.
The following table shows which kind of modules are supported by Allegro by port type:
Port type | original or branded Intel modules | non-Intel branded modules |
---|---|---|
built-in SFP+ ports | x | - |
SFP+ expansion | x | x |
SFP28 expansion | x | x |
QSFP expansion | x | x |
QSFP28 expansion | x | x |
The use of Intel branded modules is mandatory for the built-in SFP+ ports. These restrictions do not apply to the additional network expansion cards (2 port and 4 port SFP+, high precision GPS card, etc.) that are available for the Allegro Network Multimeter 1000 and 3000 series. These ports accept generic modules from a wide range of vendors.
Since auto-negotiation is often not available on 1G/10G SFP+ interfaces, it may be necessary to manually set the correct speed in the `Interface Stats` section of the user interface.
QSFP+ breakout cables are NOT supported.
List of tested third-party modules
The following list of modules have been either tested by Allegro or customers and have been reported to operate. Please be aware that this can change due new module revisions.
Optics/Copper Module | Transceiver P/N | Media Type | Remarks |
---|---|---|---|
SFP+ | Intel E10GSFPSR | Fiber (SR) | supports 1G and 10G operation |
SFP+ | Intel E10GSFPLR | Fiber (LR) | supports 1G and 10G operation |
SFP+ | Intel XDACBL1M, XDACBL3M or XDACBL5M | DA(Copper, Passive) | |
SFP+ | Flexoptix P.8596.02 | Fiber (SR) | requires Intel branding, supports 1G and 10G operation |
SFP+ | Flexoptix P.1396.10 | Fiber (LR) | requires Intel branding, supports 1G and 10G operation |
SFP+ | fs.com 36431 | Fiber (SR) | requires Intel branding, supports only 10G operation, 1G does NOT work |
SFP+ | fs.com 36432 | Fiber (LR) | requires Intel branding, supports only 10G operation, 1G does NOT work |
SFP28 | Flexoptix P.8525G.01 | Fiber (SR) | recommended with Intel branding |
SFP28 | Flexoptix P.1325G.10 | Fiber (LR) | recommended with Intel branding |
SFP28 | fs.com 68000 | Fiber (SR) | requires Intel branding |
QSFP+ | Flexoptix Q.8540G.02 | Fiber (SR4) | recommended with Intel branding |
QSFP+ | Flexoptix Q.1640G.10 | Fiber (LR4) | recommended with Intel branding |
QSFP+ | FINISAR FTL4C1QE1C | Fiber (LR4) | |
QSFP+ | FINISAR FTL410QD2C | Fiber (SR4) | |
QSFP+ | FINISAR FTL410QE1C | Fiber (SR4) | |
QSFP+ | FINISAR FTL410QE2C | Fiber (SR4) | |
QSFP+ | FINISAR FTL410QE3C | Fiber (SR4) | |
QSFP+ | Amphenol 603020002, 603020005 | DA(Copper, Passive) | |
QSFP+ 40G SR BG | Cisco qsfp-40g-sr-bg P/N: 191402 | Fiber (SR4) | modules must be (re-) inserted after power up |
QSFP+ 40G SR4 | Cisco qsfp-40g-sr4 P/N: 186602 | Fiber (SR4) | modules must be (re-) inserted after power up |
QSFP+ 40G AOC | Cisco qsfp-h40g-aoc10m P/N: 187627 | Fiber (SR) | modules must be (re-) inserted after power up |
QSFP28 | Flexoptix Q.851HG.02 | Fiber (SR4) | |
QSFP28 | Flexoptix Q.161HG.10 | Fiber (LR4) | |
QSFP28 | fs.com 75308 | Fiber (SR4) |
Non-working modules
Optics/Copper Module | Transceiver P/N | Media Type | Remarks |
---|---|---|---|
QFSP+ 40/100 SRBD | Cisco qsfp-40/100-srbd P/N: 199804 | Fiber (SR) | non-standard module, does NOT work |